Professional method guide
Tape-In Hair Extensions: Professional Specification Guide
Tape-In is judged on tab width, Butterfly folding, pack architecture and how the adhesive cycle is serviced. A gram label without piece count and width is an incomplete offer.
- Supply status
- ManufacturedHairExtensionsTR manufactures the tape-in format
- Standard widths
- 4 cm · 3 cm · 2 cmConfirm width on every written order
- Butterfly Tape
- ~2 cm → ~1 cmFolds for discreet side and fine-hair placement
- Tape thickness
- ~0.8 mm nominalSubject to confirmed product specification
- Pack example
- ~50 g / ~20 piecesIllustrative configuration — may vary
- Install quantity
- Not universalAssessed per client and service plan
What Tape-In hair extensions are
Tape-In pieces are machine-cut weft segments finished with double-sided adhesive tabs. In service they usually sit as a sandwich: one tab below an isolated natural section, one above. The format suits semi-permanent length and volume where a flat attachment line and a planned retape cycle are preferred.
This page locks the manufacturing fields that make two tape offers comparable — widths, Butterfly architecture, thickness where documented, and pack logic. It does not prescribe a full-head piece count or invent adhesive life.
Catalogue context sits on the Hair Extensions hub. Quality-label definitions sit in HI-001.
How the format is constructed
Illustrative specification diagram
- Upper tab Adhesive face down
- Natural section Isolated hair between tabs
- Lower tab Adhesive face up
The hair is prepared as individual tape pieces, each with an adhesive tab at the attachment edge. Standard manufactured widths include 4 cm, 3 cm and 2 cm. For applicable formats, the finished attachment may be produced around a nominal 0.8 mm profile, subject to the confirmed product specification.
Butterfly Tape begins as an approximately 2 cm format and folds to approximately 1 cm. The fold creates a narrower footprint for temples, above the ear and other discreet placements without inventing a separate “invisible” product family.
The adhesive system is part of the manufactured piece. Replacement adhesives used at retape are professional consumables and must be specified separately when a reorder is hair-only versus a full retape programme.
A 4 cm tab spreads load across a wider adhesive face. A 2 cm tab and a folded Butterfly piece occupy less scalp real estate. That trade-off is why width belongs on the purchase order before anyone argues about “full head” piece counts.
The nominal 0.8 mm profile is a reference for applicable formats, not a universal finished measurement or absolute tolerance for every configuration.
Manufactured component versus accessory
HairExtensionsTR manufactures the tape-in extension hair with its factory adhesive tab architecture. That manufactured status does not automatically extend to every accessory a salon may use during service.
- Manufactured: tape weft pieces at approved widths, including Butterfly folding architecture where ordered.
- Professional consumables: replacement adhesive tapes, solvents and tools used at retape or removal — confirm supply separately.
- Requires confirmation: invisible or injection tape-in variants — availability requires current written product confirmation.
Do not claim that all products on a salon tray are manufactured in-house. State supply status per component.
Weight, piece count and dimension logic
Buyers often meet Tape-In as a pack weight and a piece count. A 50 g tape pack may be configured as approximately 20 pieces. Piece count can change with tab width, hair loading and the written order specification. Treat that pairing as an illustrative commercial configuration, not a universal pack standard for every 2 cm, 3 cm or 4 cm format.
Piece count alone does not describe how much hair sits in each tab, how wide each piece is, or how many rows a professional will place. A full installation quantity varies with natural-hair density, desired length change, row planning and professional assessment. Do not prescribe a universal full-head piece count on this page or in wholesale marketing copy.
Compare width, length, grams, piece count and Draw Class together. Narrower tabs distribute load differently from wider tabs; Butterfly folding changes footprint without changing the need for correct gram totals per row.
Wholesale buyers should also record whether a pack is sold as hair-with-adhesive ready for first install, or as a hair reorder intended for retape with separate consumable adhesive. Those two commercial patterns change how grams and piece counts are interpreted at receiving inspection.
When planning rows, professionals often alternate widths across levels. That service pattern does not require the factory to invent a universal row recipe; it does require the order to supply enough of each width when a mixed-width plan is intended.
Document Draw Class and Ratio beside grams. Two packs with identical piece counts can still present differently at length if drawn composition differs. Treat those fields as part of the same comparison sheet, not as optional extras.
A 50 g tape pack does not tell the buyer everything. The number of pieces, the width of each tab and the amount of hair carried by each piece still need to be stated. When a written order uses an approximately 50 g / approximately 20-piece configuration, those fields belong together on the quotation — they are not implied by width alone.
Receiving inspection should note whether the shipment is first-install hair-with-adhesive or a hair-only reorder for retape with separate consumable tape. Those two commercial patterns change how grams and piece counts are read on arrival.
Mixed-width row plans are common in service. The factory does not invent a universal row recipe; the order must supply enough of each width when a mixed plan is intended. Draw Class and Ratio sit beside grams on the same comparison sheet.
Available format variations
Documented manufactured width options include 4 cm, 3 cm and 2 cm. Butterfly Tape is the folding architecture described above. Length, colour and hair-quality fields vary by written order.
Invisible or injection tape-in constructions are outside the documented standard and Butterfly width formats on this page. Availability requires current written product confirmation.
Do not blur Tape-In with Machine Weft sew-in rows, keratin fusion tips or Clip-In hardware sets. Adjacent methods share human hair as a raw material family; they do not share attachment architecture.
Invisible or injection constructions are not defined by category labels alone. Availability requires current written product confirmation.
Do not blur Tape-In with Machine Weft sew-in rows or keratin tips. Shared human hair as a raw material family does not make attachment architectures interchangeable.
Hair-quality considerations
Origin is not a grade. Remy, Virgin, raw, ethical and traceable appear only inside the evidence definitions in HI-001.
Draw Class and Ratio change how full a tab looks at length. They do not change adhesive physics or make fine hair automatically suitable for sandwich placement.
Processed curl or wave on tape pieces is a production finish unless separately evidenced as donor curl. Front-zone work still needs colour, elevation and tab-width discipline — see Temple Hair.
Colour and texture specification
Order colour against the standard programme or a written custom brief. Check the tab zone under daylight as well as salon light; a perfect mid-length match can still fail at the sandwich line.
Rooted, balayage and highlight families need references and, where feasible, sample control. Texture — straight, body or curl — is stated on the order. A textured tape piece is not interchangeable with textured Crochet Human Hair or Butterfly Weft by texture name alone.
Conditional suitability guidance
Narrower tabs and Butterfly folding reduce footprint. They do not promise suitability for every fine-hair client. Strand strength, density, attachment load and professional assessment still decide the plan.
Compromised mid-lengths, heavy heat history or insufficient density for sandwiching may point to another method, a lighter plan, or no extension service. No medical or guaranteed-safety claims attach to the format.
Professional application overview
Section isolation, tension and alignment sit with the installer. Heat near tabs weakens adhesion; product choice around the tab zone matters as much as width selection.
Training context is on Professionals and Academy — without accreditation claims. Combination work at the hairline should name both methods in the service plan.
Maintenance and inspection principles
Retape timing follows growth, condition, install quality and inspection — not a fixed factory week count.
Look for lift at tab edges, matting in the sandwich, colour shift at the leave-out and whether the adhesive still carries the planned load. Replacement adhesive is a consumable decision at service, not a marketing calendar.
Oily scalp conditions, frequent heat at the tab line and aggressive brushing across sandwiches change outcomes. Those variables live in consultation notes, not in invented universal wear calendars.
Removal and reapplication overview
Professional removal uses approved solvents and technique to separate adhesive faces without tearing natural hair. Reapplication may reuse hair with new adhesive or require new manufactured pieces, depending on hair condition and the written service plan.
Do not describe removal as universally damage-free. Outcomes depend on prior install quality, client care and the remover’s competence.
Professional removal separates adhesive faces with approved solvents and technique. Hair may be reused with new adhesive when condition allows, or replaced. Outcomes track prior install quality and client care — not a universal damage-free promise.
Manufacturing and quality-control framework
Production in Türkiye can align cutting, tab application, width control, colour match and packing to a written specification. Inspection can weigh sample packs, measure widths and compare colour under agreed light.
That does not invent certifications, volumes or adhesive formulas. Process framing: Manufacturing.
Wholesale specification table
| Field | What to lock | Notes |
|---|---|---|
| Width | 4 / 3 / 2 cm or Butterfly | Butterfly ~2→~1 cm fold |
| Thickness | ~0.8 mm nominal, subject to confirmed specification | Not a universal finished measurement |
| Pack architecture | Grams and piece count together | Illustrative e.g. ~50 g / ~20 pieces — confirm on order |
| Length | Written length | Compare with grams and width |
| Colour / texture | Code or custom brief | Sample control where needed |
| Hair-quality fields | Draw Class, Ratio, evidence terms | Per HI-001 definitions |
| Reorder type | Hair-only vs retape programme | Consumables separate |
| Invisible / injection | Confirmation required | Not assumed catalogue |
Write every field into the order. A missing width or pack architecture is how two “tape-in” quotes become incomparable.
Write every field into the order. Missing width or pack architecture is how two “tape-in” quotes become incomparable even when both quote the same grams.
Reorder type — hair-only versus retape programme — belongs beside colour and length. Consumable adhesive supply is a separate line when the salon runs its own retape stock.
Buyer comparison checklist
- Confirm manufactured status for the hair/tab piece versus consumable retape supplies.
- Lock width set and Butterfly requirement before price talk.
- Compare grams and piece count as a pair, not in isolation.
- Refuse universal full-head piece counts presented as manufacturing facts.
- Align colour, texture and HI-001 quality language with evidence.
- Confirm invisible/injection status only from a current written product confirmation.
- Separate adhesive life marketing from inspection-led maintenance.
Keep a receiving checklist that mirrors the wholesale table: width mix, Butterfly count, grams, piece count, colour code, texture, Draw Class and whether adhesive consumables ship with the hair. Photograph sealed packs on arrival when disputes are likely.
Photograph sealed packs on arrival when disputes are likely. Mirror the wholesale table on the receiving checklist: width mix, Butterfly count, grams, piece count, colour, texture, Draw Class and whether adhesive consumables shipped with the hair.
Common specification mistakes
- Treating piece count as hair quantity without grams and width.
- Reading Butterfly Tape as a universal fine-hair promise.
- Treating fixed retape week counts as factory facts.
- Treating category labels as proof of invisible/injection catalogue status.
- Confusing Tape-In sandwich architecture with Machine Weft sew-in rows.
- Using Remy/Virgin/ethical labels without approved evidence definitions.
Another recurring error is treating Butterfly Tape as a medical fine-hair solution rather than a narrower footprint option. Concealment improvements do not rewrite strand-strength limits.
Butterfly Tape is a narrower footprint option. It is not a medical fine-hair solution. Concealment gains do not rewrite strand-strength limits.
Comparison with adjacent methods
| Topic | Tape-In | Adjacent note |
|---|---|---|
| Attachment | Adhesive tabs | Keratin uses fusion bonds; Micro Ring uses beads |
| Profile | Flat sandwich | Clip-In uses removable hardware |
| Row logic | Paired tabs | Machine Weft uses continuous sewn edge |
| Consumables | Retape adhesives | Micro Ring beads are separate consumables |
When the brief needs strand-level fusion control, read the Keratin Bond guide. For sew-in gram efficiency, see Machine Weft. For removable retail sets, see Clip-In.
Strand-level fusion control belongs on the Keratin Bond page. Sew-in gram efficiency belongs on Machine Weft. Removable retail sets belong on Clip-In. Each comparison starts from attachment architecture, not from a shared “human hair” slogan.
Custom production in Türkiye
Custom colour, length, texture, width mix and pack architecture can be manufactured when feasibility allows. Private adhesive formulas stay unpublished; buyers receive the fields needed to reorder, not a process dump.
Frequently asked questions
- Are Tape-In extensions manufactured by HairExtensionsTR?
- Yes. The tape-in format is manufactured. Replacement adhesives and tools used in salon service are professional consumables and should be confirmed separately.
- What widths are standard?
- Documented standard widths include 4 cm, 3 cm and 2 cm. Butterfly Tape begins at approximately 2 cm and folds to approximately 1 cm.
- How many pieces are in a 50 g pack?
- A 50 g tape pack may be configured as approximately 20 pieces. Piece count can change with tab width, hair loading and the written order specification.
- Is Tape-In suitable for every fine-hair client?
- No. Suitability is conditional on strand strength, density, attachment load and professional assessment. Narrower tabs and Butterfly folding may help concealment; they are not a universal fine-hair promise.
- How often must Tape-In be retaped?
- There is no invented universal week count. Maintenance depends on growth, condition, installation, inspection and professional assessment.
If a quote lists “tape-in” with only a gram total, send it back. Width and piece architecture are not optional footnotes.
Professional enquiry
Bring width, Butterfly requirement, pack architecture, length, colour, texture and hair-quality fields to the conversation. Manufacturing responds to written specifications — not to vague category labels.
Evidence and limitations. No invented prices, MOQs, lead times, warranty periods or universal install quantities. Maintenance follows growth, condition, installation and inspection. Availability of invisible or injection tape requires current written product confirmation.
Bring width, Butterfly requirement, pack architecture, length, colour, texture and hair-quality fields. Manufacturing answers written specifications — not vague category labels.